Project: Mistress

........as my 93 4dr 2wd blazer will be known here.
To date this is what is a list of what has been done to her so far,not a lot but I have a plan,sorta.
MSD 6a box
MSD 8.5mm wires
MSD blaster coil
MSD Pro billet dizzy
EGR restrictor plate
Underdrive pulleys
Optima Red top
New tps
New iac
Spectre 3.5" cai
Yota camry E-fans
New rotors,bearings,and Bendix titanium pads
Hedman long tube headers
Custom 2.5" "Y" pipe(I made it)
Cat delete
Series 40 Flowmaster 2.5 in 2.25 out(2.5 out in the near future)
New fuel pump
trap door for said fuel pump
FUTURE MODS:
Hydro boost(I have this already)
ABS delete
C5 wheels(got these already too)17X8.5 and 18X9.5
Swap '93 CPI 4.3 out for a '98 that will be either n/a or will have a 670 holley projection tbi on top of a 2114,no GM computers.
Probably do a rocker swap( heads only have about 20k on them I put them on it 2yrs ago)
Balance shaft gear delete
Lower end only has about 80k on it,and was well maintained,going to leave that alone
Thinking about a comp cams 270
Have 3.42's,want 3.73's,Anybody got 3.73's for a 7.5?
Once I figure out how to post pics,I will,most of you have seen them any way!lol

Can't wait to see it again!

I think I am going to order my intake next week,2114.Can anyone tell me if the heads from the '96 will fit in place of the heads on my '93.At this point in time I am going on the assumption that they will.I ask because I have decided to go ahead and freshen up the lower end of the '96 engine but still be able to try out the Holley projection and see how/if it works,then I don't have to rush on building the lower end and can have it the way I want it.

he '96 heads are Vortec heads, right? Does the 2114 fit Vortec heads?

he '96 heads are Vortec heads, right? Does the 2114 fit Vortec heads?

Yes,it said '96 and later,even if they are installed on earlier blocks.

Pics.............maybe.

Can I just use the img link from photobucket to post pics?

That's all I use is photobucket. I like uploading entire folder instead of one at a time crap.

These are the toyota camry fans I put in.Most of the pics for my build are in my photobucket account.Feel free to look around in ther I have nothing to hide,all I ask is for you not to upload any crap to my albums,I wouldn't do that to you.
http://s433.photobucket.com/albums/qq56/oddball0757/Efans/

Not too bad. Almost look factory in there.

Not too bad. Almost look factory in there.

Thanks Jason,they were actually pretty easy to get in there and therer is only a very little bit of the rad core left left showing. I aint real wiring smart,so yeah,they run on a toggle switch!lol

Summit has a thermo-activated fan switch.. it's about $40-45 & has a sensor that screws into the cooling system that tells the relay to pop the fan(s) on/off.

http://www.summitracing.com/parts/SUM-890016/  <- This is the ones I use. 200* on 185* off.

Summit has a thermo-activated fan switch.. it's about $40-45 & has a sensor that screws into the cooling system that tells the relay to pop the fan(s) on/off.

http://www.summitracing.com/parts/SUM-890016/  <- This is the ones I use. 200* on 185* off.

Sweeeeet,thanks Jason,bookmarked!That just made it to #2 on my to buy list!

.. you saw it when we popped the hood & you saw the wiring for the fan over in the corner.

.. you saw it when we popped the hood & you saw the wiring for the fan over in the corner.

Oh yeah,that,s right !lol. 2 many years of slammin dope has totally fvkd my short term memory,can't remember shit!Be back in a little while,gonna go order some parts!

haha.. it happens.

haha.. it happens.

Don't it though!lmao!

So that's what does it....

Your access panel looks so nice.

Your access panel looks so nice.

Thanks Eric,how ya doin?